Board Foot Calculator Desktop Header Logo
Калькулятор BD FT
Руководство • 9 ноября 2026 г.

How to Calculate Board Feet in a Standing Tree - Руководство и Расчеты (Руководство)

Руководство и Расчеты: Calculate board feet in a standing tree: measure DBH and merchantable height, ap... [Точные формулы и расчет]

How to Calculate Board Feet in a Standing Tree - Руководство и Расчеты (Руководство)

A standing tree is not measured like a cut log. You cannot put a tape on both ends, so you work from two numbers you can measure while the tree is still up: the diameter at breast height, and the merchantable height in 16 foot log lengths. This guide shows both log rules, Doyle and International 1/4 inch, so you can see why two people can give different answers for the same tree and both be using a real rule. Use the free board foot calculator to check any number in this guide against your own tree.

Direct Answer (AEO & GEO Summary): Measure the diameter at breast height, 4.5 feet up the trunk, and count the merchantable height in 16 foot logs. Apply a log rule to the small end diameter of each log and add the logs together. For the worked example in this guide, a 20 inch DBH oak with two 16 foot logs holds 269 board feet by the Doyle rule and 339 board feet by the International 1/4 inch rule. After a 25 percent milling loss, that is about 202 board feet of lumber by Doyle, or about 254 board feet by International.


What you need to measure

Two measurements decide the answer, and both are taken while the tree is standing.

  1. DBH, diameter at breast height. Measure the trunk diameter at 4.5 feet above the ground on the uphill side. Use a diameter tape, which reads diameter directly, or measure the circumference and divide by 3.1416. A 20 inch DBH oak has a circumference of about 62.8 inches.
  2. Merchantable height. Count how many 16 foot logs the trunk holds before it narrows too much to saw, usually down to about an 8 inch top diameter. A tree with 32 feet of sawable trunk holds two 16 foot logs. Estimate height with a clinometer, a marked stick, or by pacing back and sighting the top against a pole of known length.

Do not use the DBH as the log diameter in the rule. A log tapers, so the small end of each log is smaller than the DBH. A common taper is about 1 inch of diameter per 8 feet of height, which is about 2 to 3 inches per 16 foot log. For the worked example, the 20 inch DBH tree gives a butt log with a 17 inch small end and a top log with a 14 inch small end.


The Doyle rule

The Doyle rule is the oldest log rule still in common use, and it is the rule most sawmills in the eastern United States still quote. For one log:

$$\text{Board Feet} = \frac{(D - 4)^2 \times L}{16}$$

Here $D$ is the small end diameter in inches, and $L$ is the log length in feet. The minus 4 inches is an allowance for slabs, edgings, and saw kerf, and it is the reason Doyle underscales small logs. A 10 inch log loses 4 of its 10 inches before the calculation even starts.

Doyle is simple and it is the rule a buyer is most likely to use, so learn it even if you prefer the International rule. Its weakness is real: for logs under about 16 inches, it gives a figure well below what a modern mill actually cuts. Learn the same rule for cut logs in the log volume guide.


The International 1/4 inch rule

The International 1/4 inch rule is the most accurate of the common log rules, because it models a 1/4 inch saw kerf and a realistic taper instead of subtracting a flat 4 inches. For a 4 foot section of log:

$$\text{Board Feet} = 0.22 \times D^2 - 0.71 \times D$$

Multiply by the number of 4 foot sections in the log. A 16 foot log has four sections, so multiply the result by 4. Here $D$ is the small end diameter in inches.

International gives a higher figure than Doyle for the same log, and the gap is largest on small logs. It is the rule foresters use when they want the closest estimate of what the mill will actually saw. If a buyer quotes Doyle and you quote International, the difference is not an error by either side. It is two different rules.


Worked example: a 20 inch DBH oak, two 16 foot logs

This example uses a white oak with a 20 inch DBH and 32 feet of merchantable height, which is two 16 foot logs. Taper is about 3 inches per log, so the butt log has a 17 inch small end and the top log has a 14 inch small end.

Tree specification

  • Species: white oak
  • DBH: 20 inches, measured at 4.5 feet
  • Merchantable height: 32 feet, two 16 foot logs
  • Butt log small end: 17 inches
  • Top log small end: 14 inches
  • Taper: about 3 inches per 16 foot log

Step 1: Doyle rule, butt log

$$\frac{(17 - 4)^2 \times 16}{16} = 13^2 = 169 \text{ board feet}$$

Step 2: Doyle rule, top log

$$\frac{(14 - 4)^2 \times 16}{16} = 10^2 = 100 \text{ board feet}$$

Step 3: Doyle total

$$169 + 100 = 269 \text{ board feet}$$

Step 4: International rule, butt log

One 4 foot section:

$$0.22 \times 17^2 - 0.71 \times 17 = 63.58 - 12.07 = 51.51 \text{ board feet}$$

Four sections in a 16 foot log:

$$51.51 \times 4 = 206.04 \text{ board feet}$$

Step 5: International rule, top log

One 4 foot section:

$$0.22 \times 14^2 - 0.71 \times 14 = 43.12 - 9.94 = 33.18 \text{ board feet}$$

Four sections:

$$33.18 \times 4 = 132.72 \text{ board feet}$$

Step 6: International total

$$206.04 + 132.72 = 338.76 \text{ board feet, about 339 board feet}$$

Step 7: Milling loss

A standing tree does not become lumber at 100 percent. Slabs, edgings, kerf, and defects take about 25 to 30 percent. At a 25 percent loss, the usable lumber is:

  • Doyle: $269 \times 0.75 = 201.75$, about 202 board feet
  • International: $339 \times 0.75 = 254.25$, about 254 board feet

Answer for this tree: 269 board feet by Doyle, or 339 board feet by International, before milling. Expect about 202 to 254 board feet of sawn lumber after milling. Check the log figures in the standing trees calculator by entering each log diameter and length in turn.


Doyle vs International for a 16 foot log

Use nominal small end diameter in this table. The gap between the rules is largest on small logs, which is why Doyle underscales young or small trees.

Small end diameterDoyle, 16 foot logInternational, 16 foot log
10 inches36 board feet60 board feet
12 inches64 board feet93 board feet
14 inches100 board feet133 board feet
16 inches144 board feet180 board feet
18 inches196 board feet234 board feet
20 inches256 board feet295 board feet

Worked check for the 10 inch row: Doyle gives $(10 - 4)^2 = 36$ board feet, while International gives $(0.22 \times 100 - 0.71 \times 10) \times 4 = (22 - 7.1) \times 4 = 59.6$, about 60 board feet. Doyle is 40 percent lower on this small log, which is why a buyer using Doyle and a seller using International can disagree sharply on the same small tree.


Why Doyle underscales small trees

The minus 4 inches in the Doyle formula is a fixed allowance, so it takes the same 4 inches from a 10 inch log as from a 20 inch log. On a 10 inch log, that is 40 percent of the diameter gone before the calculation starts. On a 20 inch log, it is only 20 percent. The result is that Doyle is fair on large logs and harsh on small ones, and the table above shows the gap closing as diameter grows.

If you are selling small trees, ask which rule the buyer uses before you agree a price. If the buyer uses Doyle, the same tree is worth fewer board feet on paper than it would be under International, even though the mill cuts the same lumber from it.


Common mistakes with a standing tree

  • Using DBH as the log diameter. The small end of each log is 2 to 3 inches smaller than the DBH per log length, because the trunk tapers. Using DBH for every log overstates the volume.
  • Counting the whole tree height. Only merchantable height counts. The top of the tree above about an 8 inch diameter, and any crooked or forked section, is not sawable timber.
  • Forgetting milling loss. Log rule board feet are not lumber board feet. Take off 25 to 30 percent for slabs, kerf, and defects before you plan a project around the number.
  • Mixing the rules. Do not average Doyle and International, and do not apply the Doyle minus 4 inside the International formula. Pick one rule, say which one, and use it for every log.

Frequently Asked Questions (FAQ)

How do you calculate board feet in a standing tree?

Measure the DBH at 4.5 feet and count the merchantable height in 16 foot logs. Work out the small end diameter of each log, allowing about 3 inches of taper per log, then apply a log rule to each log and add them together. For a 20 inch DBH oak with two 16 foot logs, the answer is 269 board feet by Doyle, or 339 board feet by International.

What is DBH in forestry?

DBH is the diameter at breast height, measured at 4.5 feet above the ground on the uphill side of the tree. It is the standard forestry measurement for standing trees, and it is the starting point for every standing tree volume estimate.

Why is the Doyle rule lower than the International rule?

Doyle subtracts a flat 4 inches from the diameter before it calculates, which is a large share on a small log. International models a 1/4 inch saw kerf instead, so it keeps more of the small log. The gap is largest below 16 inches and narrows as logs get bigger.

How much lumber do you get from a standing tree?

Take the log rule total and subtract 25 to 30 percent for milling loss. A 20 inch DBH oak with two 16 foot logs gives about 202 board feet of lumber by Doyle, or about 254 board feet by International, after a 25 percent milling loss.

Can you use a Biltmore stick instead of a tape?

Yes. A Biltmore stick estimates DBH and merchantable height without climbing or felling the tree. It is less accurate than a diameter tape, but it is fast and it is the tool foresters use for a quick cruise of many trees.

Does the species change the board feet?

No. Board feet are a volume measure, so the same diameters and lengths give the same board feet for oak, pine, or maple. Species changes the value of the lumber and the milling loss, not the volume.