How Many Board Feet Do I Need for a Shed? Shed Lumber Calculator Guide - Руководство и Расчеты (Руководство)
Руководство и Расчеты: Work out how many board feet you need for a shed, with stud, plate, joist, rafte... [Точные формулы и расчет]
A shed is easy to under order, because the lumber hides in five different places: studs, plates, floor joists, rafters, and siding. If you count only the studs, you will be short by more than half. This guide counts all five parts, so you can order once, with a waste allowance built in. Use the free board foot calculator to check any number in this guide against your own shed.
Direct Answer (AEO & GEO Summary): For one board, board feet equal thickness in inches times width in inches times length in feet, divided by 12. For a shed, add five parts: studs, plates, floor joists, rafters, and siding. For the worked example in this guide, a 10x12 shed with 8 foot walls needs 900 board feet before waste, and 990 board feet after a 10 percent waste allowance.
What counts as board feet on a shed
Five parts count, and each one uses the same board foot formula.
- Studs. The vertical wall framing, usually 2x4, 8 feet long, spaced 16 inches apart. Count them per wall, from the wall length divided by 16 inches, plus one.
- Plates. The horizontal framing at the top and bottom of each wall. Count three plates per wall: one bottom plate and a double top plate.
- Floor joists. The floor framing, usually 2x6, spanning the short side of the shed, spaced 16 inches apart across the long side.
- Rafters. The roof framing, usually 2x6, in pairs spaced 2 feet apart along the ridge.
- Siding. The wall covering, usually 1 inch thick boards. At 1 inch thick, one square foot of wall is one board foot of siding.
Use nominal size for the board foot calculation itself. Lumber is sold by nominal size, so a 2x4 stud counts as 2 inches by 4 inches in the formula, even though its actual dressed size is smaller. Learn the same formula in the main guide, how to calculate board feet.
The shed board feet formula
For one board:
$$\text{Board Feet (BDFT)} = \frac{\text{Thickness (in)} \times \text{Width (in)} \times \text{Length (ft)}}{12} \times \text{Quantity}$$
For a whole shed:
$$\text{Total BDFT} = \text{Stud BDFT} + \text{Plate BDFT} + \text{Joist BDFT} + \text{Rafter BDFT} + \text{Siding BDFT}$$
Then add waste:
$$\text{Board Feet to Order} = \text{Total BDFT} \times 1.10$$
The 10 percent waste allowance covers cuts, short sections, and boards with knots or warp that you reject on site. Siding and decking are usually bought as plywood sheets, not by the board foot, so this guide counts board siding only. If your shed uses plywood siding, count the sheets separately and leave the siding line out of the board foot total.
Worked example: a 10x12 shed with 8 foot walls
This example uses a 10 foot by 12 foot shed, 8 foot walls, 2x4 studs at 16 inch spacing, 2x6 floor joists, 2x6 rafters, and 1 inch board siding.
Shed specification
- Size: 10 feet by 12 feet
- Wall height: 8 feet
- Studs: 2x4, 8 feet long, spaced 16 inches apart
- Plates: three per wall, 2x4
- Floor joists: 2x6, 10 feet long, spaced 16 inches apart
- Rafters: 2x6, 12 feet long, pairs spaced 2 feet apart
- Siding: 1 inch boards on all four walls
Step 1: Count the studs
A 10 foot wall is 120 inches. At 16 inch spacing, that is $120 / 16 = 7.5$ spaces, so 7 full spaces plus one end stud gives 8 studs. A 12 foot wall is 144 inches, so $144 / 16 = 9$ spaces plus one end stud gives 10 studs. Two walls of each size:
$$2 \times 8 + 2 \times 10 = 36 \text{ studs}$$
One 2x4 stud, 8 feet long:
$$\frac{2 \times 4 \times 8}{12} = 5.33 \text{ BDFT per stud}$$
$$36 \text{ studs} \times 5.33 = 192.00 \text{ BDFT}$$
Step 2: Board feet for the plates
The perimeter is $2 \times (10 + 12) = 44$ feet. Three plates per wall means three times the perimeter in plate length.
$$44 \times 3 = 132 \text{ linear feet of plate}$$
One linear foot of 2x4 plate:
$$\frac{2 \times 4 \times 1}{12} = 0.67 \text{ BDFT per linear foot}$$
$$132 \times 0.67 = 88.00 \text{ BDFT}$$
Step 3: Board feet for the floor joists
Joists span the 10 foot side and are spaced across the 12 foot side. The 12 foot side is 144 inches, so $144 / 16 = 9$ spaces plus one end joist gives 10 joists.
One 2x6 joist, 10 feet long:
$$\frac{2 \times 6 \times 10}{12} = 10.00 \text{ BDFT per joist}$$
$$10 \text{ joists} \times 10.00 = 100.00 \text{ BDFT}$$
Step 4: Board feet for the rafters
The ridge runs along the 12 foot side. Pairs spaced 2 feet apart give $12 / 2 + 1 = 7$ pairs, which is 14 rafters.
One 2x6 rafter, 12 feet long:
$$\frac{2 \times 6 \times 12}{12} = 12.00 \text{ BDFT per rafter}$$
$$14 \text{ rafters} \times 12.00 = 168.00 \text{ BDFT}$$
Step 5: Board feet for the siding
Wall area is the perimeter times the wall height:
$$44 \times 8 = 352 \text{ square feet}$$
At 1 inch thick, one square foot of siding is one board foot:
$$352 \text{ BDFT}$$
Step 6: Add the five parts and add waste
$$192.00 + 88.00 + 100.00 + 168.00 + 352.00 = 900.00 \text{ BDFT before waste}$$
With a 10 percent waste allowance:
$$900.00 \times 1.10 = 990.00 \text{ BDFT}$$
Answer for this shed: order 990 board feet. Check the result in the lumber calculator by entering each board size and quantity in turn, and check the wall framing in the wall calculator.
Board feet by shed size
This table uses the same method as the worked example: 8 foot walls, 2x4 studs at 16 inch spacing, three plates per wall, 2x6 joists, 2x6 rafters in pairs every 2 feet, and 1 inch board siding. Totals are before waste, and the order figure adds 10 percent waste.
| Shed size | Studs | Total before waste | Order with 10 percent waste |
|---|---|---|---|
| 8x10 | 30 | 728 board feet | 801 board feet |
| 10x12 | 36 | 900 board feet | 990 board feet |
| 12x16 | 46 | 1,177 board feet | 1,295 board feet |
| 12x20 | 52 | 1,373 board feet | 1,511 board feet |
Worked check for the 8x10 row: 30 studs at 5.33 board feet each give 160 board feet, plates give 72, joists give 64, rafters give 144, and siding gives 288, for a total of 728 board feet. With 10 percent waste, $728 \times 1.10 = 800.8$, rounded up to 801 board feet.
Waste factor for a shed
Use 10 percent waste for a simple rectangular shed on flat ground. Use 15 percent if any of these apply.
- The shed has windows or a wide door, which create short studs and offcuts.
- The roof is not a simple gable, so rafters need angled cuts.
- You are buying rough sawn lumber, where some boards will have knots, warp, or splits.
- The shed has a loft or a second level of framing.
Do not use a waste factor below 10 percent for a shed. Offcuts from a stud are rarely long enough to use as another stud, so short pieces are mostly waste.
How to estimate the cost of shed lumber
Do not use a national price from the internet for your order. Lumber prices change by region, species, grade, and supplier, so use this method instead.
- Work out your total board feet to order, including waste, using the steps above.
- Ask your lumber yard for its price per board foot for the species and grade you want.
- Multiply total board feet by that price per board foot.
- Add roofing, plywood floor and roof decking, doors, windows, and hardware separately, because those are not sold by the board foot.
If a yard quotes by the piece instead of by the board foot, convert the quote first. Multiply the price per stud by the number of studs, the price per joist by the number of joists, and so on, then add the totals. That total should be close to the board foot total above, and a large gap means one of the two counts is wrong. Read the cost method in how to estimate lumber cost before you buy.
Frequently Asked Questions (FAQ)
How many board feet do I need for a 10x12 shed?
A 10x12 shed with 8 foot walls needs 900 board feet before waste, and 990 board feet after a 10 percent waste allowance. That is 192 board feet of studs, 88 of plates, 100 of floor joists, 168 of rafters, and 352 of siding.
How many board feet do I need for a 12x16 shed?
A 12x16 shed with 8 foot walls needs 1,177 board feet before waste, and 1,295 board feet after a 10 percent waste allowance. See the size table above for the full breakdown by shed size.
How many studs are in a 10x12 shed?
36 studs, using 2x4 studs at 16 inch spacing. Each 10 foot wall has 8 studs and each 12 foot wall has 10 studs. Add extra studs around the door and any windows, because the count above is for plain walls only.
Do rafters and floor joists count in board feet?
Yes. In the 10x12 example, rafters are 168 board feet and floor joists are 100 board feet, which together are about 30 percent of the total before waste. If you count only the studs, you will be short by that amount.
Should I use nominal or actual sizes for shed lumber?
Use nominal size for the board foot calculation, and actual spacing for counting studs and joists. A 2x4 stud is 2 inches by 4 inches in the board foot formula, even though its actual dressed size is smaller. Read the full comparison in the nominal vs actual dimensions guide.
How much extra lumber should I buy for a shed?
Buy 10 percent extra for a simple rectangular shed, and 15 percent extra if it has windows, a wide door, a non gable roof, or rough sawn lumber. In the worked example, that means 990 board feet at 10 percent.
Related Tools & Woodworking Guides
- Board Foot Calculator, the main calculator for any board size
- Lumber Calculator, check a single board size or build a cut list
- Wall Calculator, stud and plate counts for framed walls
- Deck Calculator, joists and boards for decking
- How to Calculate Board Feet, the full board foot formula guide
- How Many Board Feet for a Fence, board feet for a fence project
- How Many Boards Do I Need, board counts for other projects