How Many Board Feet Do I Need for a Fence? Fence Board Calculator Guide - Руководство и Расчеты (Руководство)
Руководство и Расчеты: Work out board feet for a fence: picket, rail and post formulas, a worked 100 ft... [Точные формулы и расчет]
A fence is easy to under order. Pickets look small on their own, but a long run adds up fast, and rails and posts add a large share on top. If you count only the pickets, you will be short on the day you build. This guide shows the full count, so you can order once, with a waste allowance built in. Use the free board foot calculator to check any number in this guide against your own fence.
Direct Answer (AEO & GEO Summary): For one board, board feet equal thickness in inches times width in inches times length in feet, divided by 12. For a fence, add three parts: pickets, rails, and posts. For the worked example in this guide, a 100 foot privacy fence with 6 foot 1x6 pickets, two 2x4 rails per section, and 4x4 posts every 8 feet needs 945 board feet before waste, and 1,040 to 1,087 board feet after a 10 to 15 percent waste allowance.
What counts as board feet on a fence
Three parts count, and each one uses the same board foot formula.
- Pickets. The vertical boards that form the fence face. Count them from the fence length and the actual width of one picket, not the nominal width. A 1x6 picket is 6 inches by name, but its actual dressed width is 5.5 inches, so it covers 5.5 inches of fence run.
- Rails. The horizontal boards that the pickets are fixed to. Most privacy fences use two rails per section. A rail is usually a 2x4, 8 feet long.
- Posts. The vertical supports set in the ground. Posts are usually 4x4, 8 feet long, spaced 8 feet apart.
Use nominal size for the board foot calculation itself. Lumber is sold by nominal size, so a 1x6 picket counts as 1 inch thick and 6 inches wide in the formula, even though its actual dressed size is smaller. Use actual width only to work out how many pickets cover the fence run.
The fence board feet formula
For one board:
$$\text{Board Feet (BDFT)} = \frac{\text{Thickness (in)} \times \text{Width (in)} \times \text{Length (ft)}}{12} \times \text{Quantity}$$
For a whole fence:
$$\text{Total BDFT} = \text{Picket BDFT} + \text{Rail BDFT} + \text{Post BDFT}$$
Then add waste:
$$\text{Board Feet to Order} = \text{Total BDFT} \times 1.10 \text{ to } 1.15$$
The 10 to 15 percent waste allowance covers cuts, gate framing, sloped ground, and boards with knots or warp that you reject on site. Learn the same formula in the main guide, how to calculate board feet.
Worked example: a 100 foot privacy fence
This example uses a 6 foot high privacy fence, 100 feet long, with no gap between pickets.
Fence specification
- Length: 100 feet, which is 1,200 inches
- Height: 6 feet
- Pickets: 1x6, 6 feet long, actual width 5.5 inches, no gap
- Rails: two 2x4 rails per section, 8 feet long
- Posts: 4x4 posts, 8 feet long, spaced 8 feet apart
Step 1: Count the pickets
$$\text{Pickets} = \frac{1,200 \text{ inches}}{5.5 \text{ inches per picket}} = 218.18$$
Round up, because a part picket still needs a full board. You need 219 pickets.
Step 2: Board feet for the pickets
One 1x6 picket, 6 feet long:
$$\frac{1 \times 6 \times 6}{12} = 3.00 \text{ BDFT per picket}$$
$$219 \text{ pickets} \times 3.00 = 657.00 \text{ BDFT}$$
Step 3: Board feet for the rails
100 feet divided by 8 feet gives 12.5 sections. Round up to 13 sections, with the last section cut to fit.
$$13 \text{ sections} \times 2 \text{ rails} = 26 \text{ rails}$$
One 2x4 rail, 8 feet long:
$$\frac{2 \times 4 \times 8}{12} = 5.33 \text{ BDFT per rail}$$
$$26 \text{ rails} \times 5.33 = 138.67 \text{ BDFT}$$
Step 4: Board feet for the posts
13 sections need 14 posts, one at each end of every section.
One 4x4 post, 8 feet long:
$$\frac{4 \times 4 \times 8}{12} = 10.67 \text{ BDFT per post}$$
$$14 \text{ posts} \times 10.67 = 149.33 \text{ BDFT}$$
Step 5: Add the three parts and add waste
$$657.00 + 138.67 + 149.33 = 945.00 \text{ BDFT before waste}$$
With a 10 percent waste allowance:
$$945.00 \times 1.10 = 1,039.50 \text{ BDFT, round up to 1,040 BDFT}$$
With a 15 percent waste allowance, use this on sloped ground or with a gate:
$$945.00 \times 1.15 = 1,086.75 \text{ BDFT, round up to 1,087 BDFT}$$
Answer for this fence: order 1,040 board feet on flat ground, or 1,087 board feet if the ground slopes or the fence has a gate. Check the result in the lumber calculator by entering each board size and quantity in turn.
Board feet per picket and per rail
Use nominal size in this table. Length is 6 feet for pickets and 8 feet for the rail.
| Board | Nominal size and length | Board feet per board |
|---|---|---|
| Picket | 1x4, 6 feet | 2.00 |
| Picket | 1x6, 6 feet | 3.00 |
| Picket | 5/4x6, 6 feet | 3.75 |
| Rail | 2x4, 8 feet | 5.33 |
Worked check for the 5/4x6 picket: 5/4 means 1.25 inches thick, so $1.25 \times 6 \times 6 / 12 = 3.75$ board feet. For an 8 foot picket, multiply the 6 foot figure by 8 and divide by 6. A 1x6 picket that is 8 feet long is $3.00 \times 8 / 6 = 4.00$ board feet.
Waste factor for a fence
Use 10 percent waste for a straight fence on flat ground with no gate. Use 15 percent if any of these apply.
- The ground slopes, so pickets need cutting to follow the slope.
- The fence has a gate, which needs extra framing and bracing.
- You are buying rough sawn lumber, where some boards will have knots, warp, or splits.
- The fence run has corners and short sections, which create offcuts.
Do not use a waste factor below 10 percent for a fence. Offcuts from a picket are rarely long enough to use as another picket, so short pieces are mostly waste.
How to estimate the cost of fence lumber
Do not use a national price from the internet for your order. Lumber prices change by region, species, grade, and supplier, so use this method instead.
- Work out your total board feet to order, including waste, using the steps above.
- Ask your lumber yard for its price per board foot for the species and grade you want.
- Multiply total board feet by that price per board foot.
- Add posts, concrete, screws or nails, and gate hardware separately, because those are not sold by the board foot.
If a yard quotes by the piece instead of by the board foot, convert the quote first. Multiply the price per picket by the number of pickets, the price per rail by the number of rails, and the price per post by the number of posts, then add the three totals. That total should be close to the board foot total above, and a large gap means one of the two counts is wrong.
When to use the other calculators instead
- Use the deck calculator if your project is decking, not a fence. Decking uses joists and boards, and the spacing rules are different.
- Use the lumber calculator to check any single board size in this guide, or to build a cut list for a fence with mixed board sizes.
- Use the weight calculator if you need to know how much the fence lumber will weigh for transport, because green lumber weighs far more than kiln dried lumber of the same size.
- Use the wall calculator for framed walls, not for fences. A fence has no studs, plates, or sheathing, so wall framing counts do not apply.
Frequently Asked Questions (FAQ)
How many board feet are in one fence picket?
A 1x6 picket that is 6 feet long is 3.00 board feet. A 1x4 picket of the same length is 2.00 board feet, and a 5/4x6 picket of the same length is 3.75 board feet. These figures use nominal size, which is how lumber is sold.
How do I calculate board feet for a 6 foot privacy fence?
Count the pickets from the fence length divided by the actual picket width, then multiply by the board feet per picket. Then add rails and posts the same way. For a 100 foot run with 1x6 pickets, two 2x4 rails per section, and 4x4 posts, the total is 945 board feet before waste, and 1,040 to 1,087 board feet after waste.
Do fence rails and posts count in board feet?
Yes. Rails and posts are a large part of the total. In the worked example, rails are 138.67 board feet and posts are 149.33 board feet, which together are about 30 percent of the total before waste. If you count only pickets, you will be short by that amount.
Should I use nominal or actual sizes for fence boards?
Use nominal size for the board foot calculation, and actual width for counting how many pickets cover the fence run. A 1x6 picket is 1 inch by 6 inches in the board foot formula, but it covers only 5.5 inches of fence run, because its actual dressed width is 5.5 inches. Read the full comparison in the nominal vs actual dimensions guide.
How much extra lumber should I buy for a fence?
Buy 10 percent extra for a straight fence on flat ground, and 15 percent extra for a sloped site, a fence with a gate, or rough sawn lumber. In the worked example, that means 1,040 board feet at 10 percent, or 1,087 board feet at 15 percent.
How much does a wood fence cost per board foot?
There is no single price to quote here, because lumber prices change by region, species, grade, and supplier. Work out your total board feet first, then multiply by the price per board foot quoted by your local lumber yard on the day you order. Read the cost method in how to estimate lumber cost before you buy.
Related Tools & Woodworking Guides
- Board Foot Calculator, the main calculator for any board size
- Lumber Calculator, check a single board size or build a cut list
- Deck Calculator, joists and boards for decking
- Weight Calculator, lumber weight for transport
- How to Calculate Board Feet, the full board foot formula guide
- How Many Boards Do I Need, board counts for other projects