Board Foot Calculator Desktop Header Logo
BD FT ক্যালকুলেটর
Forestry Calculator

গাছের কাঠ পরিমাপ ক্যালকুলেটর

বুক-উচ্চতার ব্যাস (DBH) ও ব্যবহারযোগ্য কাণ্ডের উচ্চতা থেকে একটি দাঁড়ানো গাছের বোর্ড ফুট ও কাঠের ফলন অনুমান করুন।

Short answer: with the Doyle rule, board feet = ((DBH minus 4) squared / 16) x merchantable height in feet. An 18 inch tree with 32 feet of usable height gives 392 board feet before waste.

Tree Measurement

Enter tree dimensions to estimate board foot yield

Tip: DBH is measured at 4.5 feet above ground. Merchantable height is the usable length from stump to first major defect or branch.

Doyle Rule

Most conservative estimate. Formula: ((D-4)²/16) × L. Best for smaller diameter logs (12-28"). Commonly used in eastern US.

Scribner Rule

Moderate estimate based on diagram method. Most widely used in US. Provides middle-ground between Doyle and International rules.

International Rule

Most accurate for large logs. Formula based on cylinder volume with taper. Preferred for hardwoods and large diameter timber.

প্রায় জিজ্ঞাসিত প্রশ্নাবলী

What is DBH and how do I measure it?
DBH (Diameter at Breast Height) is measured at 4.5 feet above ground level. Use a diameter tape or measure circumference and divide by π (3.14159).
Which log rule should I use?
Doyle for smaller logs (12-28" diameter), Scribner for general use (most common in US), International for large logs and hardwoods. Check local standards.
What is a typical waste factor?
15-25% is typical. Factors include: bark loss, sawdust (kerf), defects, taper, and trimming. Higher quality trees have lower waste.
How many board feet are in an 18 inch tree?
Using the Doyle rule, an 18 inch DBH tree with 32 feet of merchantable height gives 392 board feet before waste, or 333.2 board feet after a 15 percent waste factor. Scribner gives 431.92 board feet and International gives 520.99 board feet for the same tree, before waste.
Why do Doyle, Scribner, and International give different numbers?
Each rule was built for different log sizes and regions. Doyle is the most conservative and underestimates small logs. Scribner sits in the middle and is the most widely used in the US. International is the most accurate for large logs and hardwoods. Always agree the rule with your buyer before you sell.
How do I estimate the value of a standing tree?
Multiply the net board feet by your local price per board foot. For example, 333.2 net board feet at $1.50 per board foot is worth about $499.80. Check local timber prices, because species and log quality change the price per board foot a lot.

How to work out board feet for a tree, in plain words

Formula: with the Doyle rule, board feet = ((DBH minus 4) squared / 16) x merchantable height in feet, where DBH is the trunk diameter in inches at 4.5 feet above the ground. Doyle is the most conservative rule, so it gives the lowest number. Scribner and International use different formulas on the same two measurements and give higher numbers for the same tree.

Worked example: take one tree with an 18 inch DBH and 32 feet of merchantable height. Doyle: ((18 minus 4) squared / 16) x 32 = (196 / 16) x 32 = 392 board feet. Scribner: (0.79 x 324 minus 36 minus 4) x 2 = 431.92 board feet. International: (0.905 x 324 minus 32.72) x 2 = 520.99 board feet. After a 15 percent waste factor, the three rules give 333.2, 367.13, and 442.84 board feet. At $1.50 per board foot, the Doyle net yield is worth about $499.80.

Common mistakes: measuring DBH at the wrong height, counting height up to the top of the tree instead of the merchantable height, and forgetting the waste factor. Measure DBH at exactly 4.5 feet above the ground, and stop the height where the trunk branches or the diameter drops below saw log size.

When to use this method: use this calculator for a single standing tree or a small stand, and agree the log rule with your buyer first, because the rule changes the number by up to a third. For the full method with a second worked example, read our guide on how to calculate board feet in a standing tree, and use the logs calculator once the tree is cut into logs.

বিশেষায়িত ক্যালকুলেটরসমূহ

নির্দিষ্ট কাঠ এবং ব্যবহারের জন্য আমাদের বিশেষায়িত বোর্ড ফুট ক্যালকুলেটর থেকে বেছে নিন

🔗 Explore More Timber & Forestry Tools

Estimate log volume, standing trees, lumber yield, or wood weight with our specialized tools: